Press ENT. The Component Select button light turns off. Press the corresponding Component Select button for the component you have set up. Before starting the Search function Set each component to the following status so that the Search function works effectively. To cancel setup, press SET. Operating Your Components with the Remote Commander When you operate a non-Sony component, make sure you set the component code first page 8. Note The remote control signals may be different for some components or functions.
In this case, program the remote control signals with the Learning function page Page 15 Press and hold SET for over 3 seconds.
Page 16 Programming signals of another remote control — Learning Function continued Press and hold the button on the other remote control, until both the SET indicator and the Component Select button lights up again.
Page 19 Press and hold the button on the other remote control, until the SET indicator lights and all the Component Select buttons flash again. Page Advanced Features Advanced Features Controlling the Volume of Visual Components Connected to an Audio System The Commander is factory preset based on the assumption that you hear the sound of your visual components from your TV speakers, and that you hear sound of your audio components from the loudspeakers connected to your amplifier.
All Component Select buttons light up when you press these buttons, and then turn off when you release them. If you About the order of operation steps Some of the components may not accept consecutive remote control signals. To execute the commands programmed on a Component Select button by the System Control function, press the button for more than 2 seconds. Page To Clear Programmed Commands Programming a series of commands to on the Component Select buttons continued To clear programmed commands Press and while holding SET, press and hold for more than 3 seconds the Component Select button you want to clear.
Page Troubleshooting Search function. Page 36 For the customers in the U. A Customer Support Information After you have read through this manual, if you still cannot get the Remote Commander to work properly, call the Sony Customer Support Helpline at To change the channel.
Page 44 Printed in China Print page 1 Print document 44 pages. Rename the bookmark. Enter the four-digit code as found on the code list, followed by [Ent] to save. If the [Set] LED flashes five times the code number entered was invalid, try again.
Note: it is not necessary to reconfigure a component button to control a particular type of device, as this is done automatically when a code is entered.
All component buttons except for [TV] can be changed from their default device type. Entering a new preset code will not erase buttons that contain a learned signal. When your device turns on or off, press [Ent] to save. Note: when all available codes for a device category have been searched through, the component LED will flash three times. If the remote has been programmed in the past and code search does not appear to be working , enter the default Sony preset code to ensure that the button is set to control the correct type of device.
Now choose the component followed by the specific button you would like to learn a signal on. To learn a command on a Component Select or System Control button: Follow the directions above but press and hold the component or system button for three seconds or until the [Set] LET starts to flash. If the [Set] LED flashes twice the button already contains a learned signal and must be reset see instructions below. If the [Set] LED flashes five times the code did not capture correctly, try again.
Program a micro macro anywhere! Line up every remote with all the commands you need, then when learning quickly press all buttons in order.
You should be able to learn a 3 or 4 step macro in this manner onto any button. Now press and hold the component button and the button under that component that you would like to clear.
For Component Select or System Control buttons: Hold [Set] for three seconds or until the [Set] LED illuminates and, before releasing [Set], press the component or system button you would like to clear. As the command is cleared the [Set] LED will turn off. While holding the [Stop] key, press the Component Select button you would like to clear.
As commands are cleared all component LEDs will turn off. Program System Control or Component Select macros:. When finished, press [Set] to save. To play Component Select macros back you must hold the button for two seconds. If the [Set] LED flashes twice the button already contains a macro and must be reset see instructions below. Note: if a component or system button contains a learned signal it will take operational precedence over the macro. Hold [Set] and the Component Select or System Control button you would like to reset for three seconds.
0コメント